Skip to content
Consultation Partner

Honestly answered.

A paint that heats sounds too good to be true. That's why we ask the critical questions ourselves here – and also tell you when heating paint is not the best choice.

Weighing up

What speaks for it. What you should know.

+What speaks for it

  • Final documentation for every project: plans, photos, thermal images and acceptance report
  • Invisible under paint, plaster or tiles – only 0.4 to 0.6 mm thin
  • No radiators, no boiler room, no water in the system
  • Retrofit with minimal effort, without new screed
  • 24-volt low voltage in the room
  • Controlled room by room – heating only when needed
  • Radiant heat: comfortable, barely any air movement, barely any dust
  • Actively dries out damp masonry
  • Works well with photovoltaics and all-electric buildings
  • 7-year manufacturer's warranty on the heating surfaces (private customers, authorised installation)

!What you should know

  • Does not replace insulation; exterior walls require thermal decoupling
  • Heating surfaces should remain unobstructed – not permanently behind furniture or thick rugs
  • With wood, laminate and vinyl floors, only approved floor coverings
  • No DIY: installation only by certified specialist contractors
  • Copper strips and supply cables must not be drilled into – their position is recorded in the final documentation
The proof · Thermal imaging camera

Invisible to the eye. Visible to the camera.

Before it is painted over, the heating paint appears as a black surface. In operation, the thermal imaging camera shows where the heat is generated: right there, across the entire surface.

Heating paint before painting over: wall, living space Thermal image in operation: wall, living space Photo · before painting overThermal image · in operation
coolwarm
Real CARBON4® projects. Photo and thermal image always show the same room.
The most common objections

Critical questions. Clear answers.

We hear these questions in consultations and read them in forums. Here are our answers.

“A paint that heats – is that for real?”

Yes. CARBON4® heating paint is an infrared surface heating system: a conductive coating between two copper strips, operated at 24 volts. When current flows through the surface, it heats up. Thermal images from real projects show this. CARBON4® has been developing the system in Villach since 2013, and its products are in use in 27 countries.

“Isn't a heat pump more efficient?”

A heat pump additionally uses ambient heat, but needs an outdoor unit, pipework, hydraulics and regular maintenance to do so. Heating paint converts electricity directly into heat, needs none of that, and heats room by room only where heat is needed. Which solution is more economical depends on the building – we'll do the honest maths for you.

“Is electricity from my own photovoltaic system enough in winter?”

What matters is the interplay of PV, battery storage and energy manager. It is important to have a battery large enough to cover one day's heating demand. An energy manager buys and sells electricity on the exchange: it uses electricity when there is a surplus and supplies it when it is needed. This can cut energy costs significantly. We plan this realistically for your building.

“Can I still hang pictures or drill?”

Yes. You can drill into the heating surface up to the size of a socket box; nails and wall plugs are no problem. The only thing to watch out for is the copper strips – your final documentation shows where they run.

“What about furniture in front of the wall?”

Heating surfaces are planned where they will remain unobstructed. A permanently covered surface releases less heat into the room. That's why furnishing and usage are part of the planning – and why the ceiling is often the best heating surface.

“Are there hot spots?”

Not with professional installation. The installation rules specify uniform layer thicknesses and surfaces without points or corners. That's why heating paint is installed exclusively by trained, certified partner companies.

“Does heating paint create electrosmog?”

Only extra-low voltage of 24 volts is present in the room. Electromagnetic compatibility was independently tested by Carinthia University of Applied Sciences in Villach; the results confirm compatibility in intended operation.

“Does it work in the bathroom under tiles?”

Yes – the bathroom is an ideal place to use it. On walls and ceilings the heating paint sits invisibly under filler and tiles. On the floor it ensures warm feet: there it lies between a primer and an electrically non-conductive waterproofing approved by CARBON4®, followed by flexible tile adhesive and tiles. Written screed approval is required before work begins.

“So I don't need insulation any more?”

It does. The heating paint does not replace insulation and plays to its strengths in well-insulated buildings. In existing buildings, thermal separation on the inside of external walls is mandatory: insulation boards at least 2 cm thick ensure that the heat stays in the room and does not flow into the masonry.

“What happens if something breaks?”

The system needs very little maintenance: no water, no moving parts. The transformers are robust iron-core transformers without electronic components, and the control cabinet meets industrial standards. CARBON4® gives private customers a 7-year manufacturer's warranty on the heating surfaces if an authorised specialist contractor installs them. Should a component fail after all, the electrician replaces it with an identical part.

Fair comparison

Heating paint, heat pump, infrared panel.

Every system has its strengths. What matters is what suits your building.

CARBON4® heating paintHeat pumpInfrared panel
Where is the heat generated?Across the surface of wall, ceiling or floorOutdoor unit + radiators or underfloor heatingIn the panel on the wall or ceiling
Visible in the room?NoRadiators or outdoor unitYes, as a device
Installation in existing buildingsWith minimal effortUsually requires pipes and hydraulicsSimple mounting
Space requiredTechnology on max. 1 m² (single-family home)Outdoor unit, often a plant roomPanel on wall or ceiling
Type of heatRadiantConvection or radiant, depending on the systemRadiant
MaintenanceVirtually noneRegularly recommendedVirtually none
ControlRoom by roomUsually centralPer panel
To be honest

Our advice for every case.

Heating paint suits many buildings – but not every one. We'll tell you openly what we recommend. Even if, now and then, it isn't heating paint.

Existing building without insulation

Our advice

Insulate or thermally decouple first, then heat. With the right preparation, heating paint becomes a strong solution. Without it, we advise against it – too much heat would go into the masonry.

Heat pump with underfloor heating already installed

Our advice

In that case, heating paint is ideal for supplementing individual rooms such as the bathroom, attic or conservatory. We don't recommend replacing the existing heating here.

Walls fully taken up

Our advice

Then the ceiling becomes the heating surface – it always stays free. If there's no room there either, we'll tell you openly.

Is heating paint right for your building?

We'll tell you honestly – in a free initial consultation.

Request a consultation →Call